Having the best tool for your woodwork and DIY validates your professionalism in your vocation. Among others, having a perfect crosscut sled provides an exact crosscut on your table saw. The main factor is having a perfect tool. Having anything isn’t equal to having everything. To avoid the frustration that comes with using any kind of tool, I have compiled the best crosscut sleds.Crosscut sled is also know as miter sled for the table saw.
Crosscut sleds are designed to make accurate and exact cuts. This is because they are connected literally to your table saws or circular saws. They are fixed at 90 degrees to the blade for a perfect finishing without tear-out. Not just that, crosscut sleds increase the versatility of your table saw through the addition of clamps.
Crosscut sleds clasp the workpieces at an angle to be cut by your table saw or bandsaw. Also, they are more controllable than the regular miter gauge. But yet, having the precise one that fits your project is what brings about perfection. Let’s go through together the best crosscut sled for your project.
8 Best Crosscut Sleds
1. Rockler Woodworking Table Saw Crosscut Sled
Easy to assemble, accurate, thick, easy to read table saw crosscut sled.
Are you looking for an exact crosscut sled that delivers accurate woodwork results? Rocker woodworking crosscut sled is what you are looking for. It comes with a large protractor scale. This scale helps to perfectly align your angle for a perfect crosscut. Not just that, it is designed with one-half degree graduation and a visible indicator for error-free layout.
Rockler woodworking crosscut sled is ½” thick. Also, its melamine coating MDF table has a dimension of 23-¾” x 23-¾”. It has a strong aluminum fence, a flexible MDF fence face, and steady-sliding components which fosters its versatile functionality.
The right horizon of the sled works as a chip breaker. It has 4 two pieces ¾ inch broad minimal-friction tape. This enhances the smooth gliding of the fence. Its aluminum fence has a dimension of 3″ x 25″.
This crosscut sled’s MDF fence face has a dimension of 2-⅞” x 27″. Besides, the fence face can be replaced when needed. The ball bearings in the miter bar have flexible tension to eradicate slop. The sled can be stopped at an angle of 90°.
The length between the right horizon of the miter bar and the uncut part is 6inches. This cross-cut sled needs a miter track with a depth of ¾” x ⅜”. Moreover, no batteries are required for its functionality.
|Used with||Table saws|
2. Rockwell Crosscut Sled
Accurate, easy-to-install, stress-free crosscut sled.
Rockwell brand is known for producing strong and lasting products with versatility in function. Among others, Rockwell’s crosscut sled is another accurate crosscut sled for perfect cuts.
It is built with a dimension of 17.25 x 12.5 x 2.5 inches for flexibility in function. Its flexible weight of 7.04 ounces makes it easy to handle.
It produces perfect crosscuts across 90 degrees on your project. Also, it is built with an integrated scale for accurate and exact measurement. Besides, it holds the material to be cut still at a fixed point. These features foster its special characteristics. Added to its feature is a cutting groove that enables simple alignment.
Among other sleds, its easy-to-install feature makes it distinct. You just need to fix the sled into its slot. No need to hire a technician or expert. It needs no battery for its operation. Moreover, it does not work with table saws but for Rockwell saws.
|Product dimension||17.25 x 12.5 x 2.5 inches|
3. Incra Table Saw Miter Sled
Miter gauge, telescoping fence, precise miter sled.
Incra table saw miter sled is designed with a dimension of 37.8 x 25.9 x 3.7 inches for versatility in its function. It is built with a clamping fixture and T-track for precise crosscut on the workpiece. Its precise cut characteristics are also enabled via its stop positioner and clamping sled. With these features, every cut is predictable and exact. Incra table saw miter sled is best known for making precise cuts.
For a perfect cut, the Incra table saw miter sled is built with 364 angle stops. Also, it has an indexing stop of 1/2° over + or – 90° span. It has special stops of 22-1/2° and 67-1/2°.
Also added to its feature is a standard microplate miter head. It has a glide lock miter bar whose width is adjustable in ten places. It has a flip stop fence with lengths ranging from 36″- 64″.
Moreover, the T-tracks are inscribed in the MDF panel top to hold-down the workpiece. Besides, with its hold-down clamps, workpieces are fixed to the sled for an accurate cut.
Designed with the sled are ten expansion disks that modify the bars for zero side play and eliminates friction. Also, no batteries are needed for its performance. Moreover, with its weight of 31.4 pounds, it is heavy to handle.
|Product dimension||37.8 x 25.9 x 3.7 inches|
|Used with||Table saws|
4. Bora Circular Saw Sled
Easy to use, precise, versatile circular saw sled.
Do you desire a perfect and exact cut on your workpiece? Bora circular saw sled gives you what you want per time. It is convenient and simple to utilize and handle. Interestingly, your circular saw can be utilized for freehand cutting while the sled is attached to it.
The sled maintains your saw straight without constraining while cutting. With its 50″ Bora WTX clamp edge saw guide, the sled makes straight cut up to 8″. This is possible due to its adjustable saw plate track which modifies from 2.1-3.5 inches. Bora circular saw sled is simple to use and connects to your circular saw in 3 different points. Interestingly, the sled functions with both left and right-handed circular saws.
The sled has an adjustable foot and nose clamp that protects the saw’s shoe. Also, pairing the sled with a WTX clamp edge makes the saw plate versatile.
Bora circular saw sled can work with any circular saw which makes it unique and versatile. It is best known for working with any circular saw. It is built with a dimension of 15 x 9 x 2 inches. Also, it weighs 1.4 pounds. This makes it easy to handle.
|Used with||Circular saws|
|Product dimension||15 x 9 x 2 inches|
5. Fulton Table Saw Crosscut Sled Kit
UHMW bars, knobs, aluminum tracks, thick DIY crosscut saw.
Table saw crosscut sled is designed for making small cuts, and repetitive length cuts. But yet, building your crosscut sled for your table saw requires the exact and perfect pieces of equipment and steps for its makeup. This cross-cut sled kit has been designed for simplicity and perfection during building.
Firstly, it comes with an easy-to-understand guide that simplifies the procedures of building a crosscut sled. Not just that, this kit comes with a UHMW bar. These bars are utilized as runners for the crosscut sled. Interestingly, UHMW does not change state during severe weather conditions. The UHMW bars has a dimension of ¾” x ⅜”.
The tracks in this crosscut sled kit are made from aluminum. Also, the knob and bolt were designed to make a stop block. The stop block prevents repetitive fence distance measurement each time you cut.
Interestingly, the kit is built with two UHMW bars that have a dimension of 19″ x ¾” x ⅜”. Also, each has two mini tracks with a length of 12″ each. Also, each kit has a ¼” by 20″ bolt and a knob.
Take note; the UHMW bars doesn’t
match RYOBI table saw track slots.
|Material||Polyethylene and aluminum|
|Package dimension||21 x 2 x 1.2 inches|
|Used with||Table saws|
6. Rockler Table Saw Small Part Sled
Aluminum, blade guard, miter track stop, MDF small part sled.
This item comprises a table saw small part sled, a miter track stop, and w blade guard.
It is designed with a dimension of 14.2 x 8.9 x 4.1 inches. It is made with aluminium and, has an MDF coated with melamine. A miter slot is built to work with it. The miter slot must have a dimension of ⅜” x ¾”.
Rockler table saw small port sled cuts at an exact angle of 90°. Besides, it has a support system that prevents small pieces of your project. getting stuck In the table saw blade. More so, it is designed with an item weight of 4.84 pounds for perfect functioning.
The sled can be modified to cut several small part dimensions. Besides, it is built with the ability to hold small parts safely while cutting with the table saw. If you have a project that covers a wide range of small scale dimension, this sled is a good choice for your project.
|Product dimension||14.2 x 8.9 x 4.1 inches|
|Used for||Cutting a wide range of small part dimensions.|
7. Zeroplay Sled Kit
Hassle-free, thick, precise, adjustable sled kit
Zeroplay sled kit is designed with a miter bar, miter bar instructions, exemplified 360 sleds and fence project, track screw hardware, track screw, and wing knob.
The Zeroplay miter bars are designed for speed and precision. You can easily fix your sled to the blade in a jiffy. This is possible due to the top-down installation of the miter bars. Not just that, the special layout of dovetail grooves allows you to fix your fence at any point. Irrespective of the angle chosen, Zeroplay miter bars keep the sled equal to the blade for an accurate cut.
This kit is designed with an easy-to-understand plan for building your sled. All that are needed ½” 14° dovetail router bit, and some plywood. With this in place, you have your versatile sled on the ground within an hour.
Zeroplay meter bar works well with any standard T-track miter space which is between 0.73″ and 0.79″ wide, and has a depth of 5/16″.
The miter bars do not operate with table saws whose tabs are cast into the top of the miter slot. For example Ryobi and craftsman.
|Used for||Building a sled|
|Product dimension||11.5 x 5.2 x 1.1 inches|
8. Rocker Table Saw Small Parts Sled
Small distance cut, aluminum T- track, precise table saw sled.
This sled is best known for cutting small lengths. It cuts tenon stock and another small length at an angle of 90° with no tear-out. It has zero-clearance support which prevents small pieces from entering the blade or throat plate of the saw.
The miter track stop of the sled reduces the sled from moving forward. Also, the blade guard that comes with the sled is adjustable for many table saws.
Also, the T-track of the sled is made of aluminum. This helps to put a halt to repeatable cuts.
The sled is designed with a dimension of 12 x 7-¼” x 3-⅛”. The height of its fence is 1- ⅛”. The peak of the stock thickness is 1 inch. Also, the dimension of the required miter slot is ¾” x ⅜”.
The sled is made of aluminum while the MDF is melamine coated.
|Used with||Table saws|
|Product dimension||12″ x 7- ¼” x 3-⅛”|
Frequently Asked Questions
- How big should a crosscut sled be?
There is no certain length for all crosscut sleds. The size of each crosscut sled is deduced by the length from the blade, and front edge.
Also, the size of any crosscut sled is based on its proposed function.
- What kind of wood do you use for a table saw sled?
There is no mandatory wood to be used for making a crosscut sled. Besides, the proposed use can determine the material to be used. Nevertheless, the common wood used for creating most crosscut sled are plywood and MDF.
- Do I need a cross cut sled?
Table saws are designed with miter gauge used for making crosscuts and other types of cuts on materials. Crosscut sleds provide support to workpieces for accurate and exact cut.
Secondly, cross cut sled enhances safety during woodwork. You cannot cut small lengths with the miter gauge without moving your hands close to it.
Thirdly, with a cross cut sled, repetitious cuts are made easy.
Lastly, crosscuts enhances accurate and exact cut on woodworks and other materials.
As stated earlier on; having anything isn’t equal to hbing everything. With the best crosscut sled, you can give your project the perfect and exact cut desired. With the best crosscut sled for table saws or circular saws, your project is delivered with high professionalism.
For your opinions and requests, send you message to the message box below. I will be glad to receive them.
Last Updated on April 11, 2021 by John G. Anderson